N° 558
|
Glue line gap detection on transparent label
On a transparent label a gap in a glue line should be detected.
|
|
N° 363
|
Længdekontrol på metalstift Længden på en metalstift skal kontrolleres under bevægelse. Metalstiften bevæger sig med en hastighed på ca. 2 m/s.
Length control of a metal rod
The length of a steel rod should be controlled. At this, the metal rod will be moved with around 2m/s during the measurement.
|
|
N° 332
|
Aftastning af defekter på et aluminiumsprofil Forhøjninger på et aluminiumsprofil skal aftastes.
Detection of super elevations of aluminum profile
Super elevations of aluminum profile should be detected.
|
|
N° 284
|
Positionkontrol af glødetråden i en pære Positionen af de enkelte glødetråde i forhold til glaskolben skal kontrolleres.
Position control of filament holders in bulbs
The position of the filament holders in clear as well as red glass bulbs should be controlled.
|
|
N° 268
|
Højhastigheds vinkelmåling, med samtidig kontrol af omdrejningsretning Vinkelpositionen på en hurtigt roterende kodeskive, skal aftastes, yder mere skal omdrejningsretningen kontrolleres.
High speed angle measurement with direction control
The angle position of a very fast rotating shaft should be measured; furthermore the direction of the rotation should be controlled
|
|
N° 261
|
Kontrol af støbemasse på SMD – LED‘er Niveauet af en optisk transparent støbemasse på SMD – LED’er skal overvåges. Kontrollen skal sikre en vis højde på støbemassen, således at man undgår overfyldning.
Overfilling control of SMD LEDs
The level of transparent casting compound in SMD LEDs should be controlled with regard to overfilling.
|
|
N° 187
|
Aftastning af position på optisk transparent label på optisk transparent plastfilm Positionen af en transparent label på en transparent film skal aftastes. Under opgaven er hastigheden på filmen nogle få m/s.
Detection of the position of optical transparent plastic label on optical transparent plastic film
The position of a transparent label on a transparent film should be detected. At this the speed of the film is in the range of a few m/s.
|
|
N° 121
|
Kontrol af rilleprofil på transperant plastlåg På et transperant låg, skal rilleprofilen kontrolleres. På ukorrekte låg er rilleprofilen manglende eller delvis manglende.
Control of the presence of straight knurling on a transparent plastic closure
On a transparent plastic closure the straight knurling should be detected. On incorrect closures the straight knurling is partly not present.
|
|
N° 111
|
Dråbekontrol med envejs lasersystem Antal så vel som volume af dråber skal kontrolleres.
Drop control with a laser through beam system
The number as well as the volume of drops should be controlled.
|
|
N° 109
|
Aftastning af svejsesøm på metalring Opgaven er at aftaste svejsesømmen på en metalring. Ringen er i bevægelse under målingen.
Detection of a welding line on a metal ring
The task is to detect the welding line on a metal ring. During the measurement, the metal ring will be turned around.
|
|
N° 108
|
Knudecheck og kontrol for defekt på monoglødetråd Knuder såvel som defekter på monoglødetråd skal aftastes. I denne applikation findes forskellige diametre og fødehastigheden kan være nogle få m/s.
Knot and defect control of mono filaments
Knots as well as defects on mono filaments and threads should be detected. At this, different diameters of filaments and threads are possible and the feed rate lies in the range of a few m/s.
|
|
N° 106
|
Stifthøjde på elektriske komponenter Højden på stifter på elektriske komponenter skal kontrolleres under produktionen.
Pin height control of electrical components
The height of the pins of an electrical component should be controlled during the production.
|
|
N° 104
|
Inline diameterkontrol på træstave Under produktionen af træstave skal diameteren kontrolleres under bevægelse.
Inline diameter control of wooden staff
During the production of wooden staff the diameter must be controlled while the rod is moved.
|
|
N° 49
|
Kontrol af eksentrisitet på aksel på elektrisk tandbørste Frekvensen såvel som amplitude på akslen på en elektrisk tandbørste skal kontrolleres.
Control of the eccentricity of the shaft of an electrical tooth brush
The frequency as well as the amplitude of the eccentric of an electric tooth brush should be controlled.
|
|