Exemplos prácticos de uso industrial

1) Selecione uma área de aplicação:
Chemical Industry (Chemische Industrie)

2) Selecione um idioma:

Folha de
dados:

APP N° 794

Presence control of a very thin oil layer
The presence of a very thin oil layer (< 1µm) should be controlled.

Folha de
dados:

APP N° 711

Param.:

Color checking of the paintwork through sight glasses
The color of liquid lacquers should be controlled in using sight glasses. It should be taken into account, that the sight glasses have a reflecting surface.

Folha de
dados:

APP N° 673

Spray jet control with a laser through beam system
The amount of liquid and the geometry of a spray jet next to the spray nozzle should be controlled.

APP N° 626

Intensity control of fluorescent additives in oil-soaked paper
The intensity of fluorescent additives in oil-soaked paper should be controlled.

Folha de
dados:

APP N° 598

Param.:

INI:

Color control of flames
The color of a flame should be controlled.

Folha de
dados:

APP N° 517

Param.:

INI:

Concentration control of a passivator in a solvent
The amount of a passivator in a solvent should be controlled.

Folha de
dados:

APP N° 459

Param.:

INI:

Plastic ring bottom side – upper side differentiation
Plastic rings which are transported on a conveyor belt should be differentiated with a view to the direction (bottom side – upper side).

Folha de
dados:

APP N° 458

Param.:

INI:

Cut off point detection on a fleece tape
The cut off line on a fleece tape should be detected. It should be taken into account, that the fleece tape as well as the cut off line is white in color, thus, there is no color difference.

Folha de
dados:

APP N° 457

Position detection of a silicon layer on a transparent plastic film
The position of a silicon layer on a transparent plastic film should be detected (frontside / backside differentiation).

Folha de
dados:

APP N° 213

Detection of the presence of foam on a liquid
The presence of the foam on a liquid should be detected. Furthermore the liquid level (+ foam, if present) should be measured simultaneously.

Folha de
dados:

APP N° 195

Color differentiation of fluorescent oil
Different oil types which are used for engines should be differentiated. At this, the natural effect of UV fluorescence of mineral oil is used. Furthermore fluorescent liquid will be added to some of the mineral oils, which allows a differentiation of the adequate types.

Folha de
dados:

APP N° 126

Color control of lacquers
The lacquer should be inline controlled. At this a special casing is used which will be plunged into the lacquer.

Folha de
dados:

APP N° 111

Drop control with a laser through beam system
The number as well as the volume of drops should be controlled.

Folha de
dados:

APP N° 55

Color control of an emulsion
The color of the emulsion which should be controlled is normally white but it can happen that the color is drifting slightly into the red or the green range. This drift must be controlled.

Folha de
dados:

APP N° 23

Kontrola barve tekočin
Kontrola tekočin npr. vode med proizvodnjo oz. procesiranjem le-te je nujno potrebna, ker lahko pride vsled onesnaženja do spremembe barve le-te, npr. rahlo modrikasta je lahko posledica onesznaženja (polucije) ali nežno bež barva je lahko posledica prosotnosti olja itd. V obeh primerih je potrebna kontrola barve vode, ki mora biti brezbarvna in prosojna.

Colored liquid control
During a water cycle process the quality of the water must be controlled. It can happen that the water becomes slightly blue (pollution) or beige (oily) in color. Both case must be detected, the water must be clean.

Aplicações

Exemplos prácticos de uso industrial

NOTICIA

FIND US ON ....

	Calibração de cores em linha em reciclados de plástico (Sistemas de medição de cores em linha)
	Test report on Inline color measurement of recyclates () (Sistema de medição de cores em linha)

	Sensor systems for recyclate control in the plastics industry for laboratory and inline use ()
	Checking the plastic type of recyclates and virgin material using NIR technology ()

	Detecção de mossas e amolgadelas em fitas de punção metálicas (N° 801)
	Distinção de componentes interiores de couro e plástico (N° 802)
	Medição de cor das tampas plásticas (N° 803)