Exemplos prácticos de uso industrial
1) Selecione uma área de aplicação:
Furniture Industry / Wood-working Industry (Möbelindustrie / Holzindustrie)
2) Selecione um idioma:
APP N° 779
|
Color-gloss control of lacquered metal sheets Lacquered metal sheets should be controlled with regard to the color and gloss. |
|
|||||
APP N° 770
|
Gloss measurement of sandpapers The gloss factor of sandpapers should be measured. |
|
|||||
APP N° 768
|
Color measurement of lacquered aluminum plates The color of lacquered aluminum plates should be measured. |
|
|||||
APP N° 767
|
Gloss measurement of painted aluminum plates The gloss factor of lacquered aluminum plates should be measured. |
|
|||||
APP N° 766
|
Gloss measurement on decorative films The gloss factor should be measured on different decorative films. |
|
|||||
APP N° 732
|
Detection of a gap between vinyl layers A gap between vinyl layers should be detected. |
|
|||||
APP N° 720
|
Color mark detection on wood plates Color marks on wood plates should be detected. It should be noted that the color marks are black, green or red lines with a width of around 2mm. |
|
|||||
APP N° 655
|
Thickness control of a transparent adhesive layer on a UV fluorescent transparent plastic film The thickness of a transparent glue on a transparent but fluorescent plastic film should be measured. |
|
|||||
APP N° 654
|
Detection of fluorescent coating on black leather A gap with a width of 5mm in the fluorescent coating on a black leather surface should be detected. |
|
|||||
APP N° 638
|
Color control of trims Trims should be color controlled. |
|
|||||
APP N° 601
|
Differentiation of diverse hazy metal parts Diverse hazy metal components should be differentiated. |
|
|||||
APP N° 592
|
Moisture control of wood pellets The moisture of wood pellets should be controlled. |
|
|||||
APP N° 581
|
Moisture control of timber The moisture of timber should be controlled. |
|
|||||
APP N° 564
|
Joint sealing color control on fiber boards The color as well as the presence of the joint sealing of fiber boards should be detected. |
|
|||||
APP N° 551
|
Lacquer surface weight control The lacquer surface weight on furniture plates should be controlled. Investigations have shown that there is a proportional relation between the color space siM - parameters of the liquid paint on the pressing roll and the surface weight of the lacquer on the panel. However, the proportionality factor is dependent of the color and has to be calibrated for the respective paint. |
|
|||||
APP N° 546
|
Differentiation of High Density Fiberboards (HDF-boards) Treated High Density Fiberboards should be differentiated. At this, one board is wood sanded, the 2nd board is wood sanded with first sealer and the 3rd board is wood sanded with first sealer and lacquer sanded. |
|
|||||
APP N° 521
|
测量阳极氧化铝板材的光泽度 应在生产线上测量不同的铝板材的光泽度。 Gloss measurement of anodized guide rails The gloss of anodized aluminum guide rails should be inline measured. |
|
|||||
APP N° 520
|
测量阳极氧化铝型材的颜色 应在生产线上测量阳极氧化铝型材的颜色 Color measurement of anodized aluminum stripes The color of anodized aluminum stripes should be measured inline. |
|
|||||
APP N° 390
|
塑料窗型材的色检 应检测塑料窗型材的颜色。 Color control of plastic window profiles Plastic profiles which are used for casement frames should be color controlled. |
|
|||||
APP N° 371
|
检查金属部件上的镀铬层 应监测一个金属部件上是否存在镀铬层。 Chromium plating presence control The presence of chromium plating on a metal part should be controlled. |
|
|||||
APP N° 365
|
上漆板材的色检 应通过颜色来区分上漆板材。在此也须检查金属漆涂层。 Color control of lacquered metal sheets Lacquered metal sheets should be color differentiated. Even metallic paints must be color controlled. |
|
|||||
APP N° 344
|
贴面胶合板的叠张监测 在贴面胶合板的运输过程中，可能出现错误抽取超过一层贴面胶合板的情况，这个过程必须加以监测。 Double sheet control of veneers During the transportation of veneers, it should be controlled whether one or more than one veneer was picked up from a handling system. |
|
|||||
APP N° 340
|
检查中密度纤维板的沟槽颜色 应监视沟槽内颜色的均匀一致性。当颜色出现错误时，中密度纤维板的底色会呈现出来。 Color control of grooves on MDF plates Grooves on MDF plates should be color controlled. In case of failure the MDF background color can be seen. |
|
|||||
APP N° 336
|
监测板材上的荧光标记 应识别木板上的荧光标记，在此必须能准确地监测到紧密相邻的两条荧光线。 Detection of fluorescent marks on wooden board Fluorescent marks should be detected on wooden boards. At this, two marks which are close together should be proper detected. |
|
|||||
APP N° 272
|
识别塑料地板上的塑料粘胶带 应识别出连接两块塑料地板端部的粘胶带。在此，塑料地板的色彩可以不同，而粘胶带则非黄色即棕色。 Detection of an adhesive tape on plastic flooring An adhesive tape, which has the task to combine the two ends of the plastic flooring, should be detected. At this, the plastic flooring can be different in color; the tape, however, is either yellow or brown in color. |
|
|||||
APP N° 271
|
识别塑料膜上的粘胶层 应识别出塑料膜上存在的粘胶层。最好应对粘胶层的整个宽度进行检查。粘胶涂层在紫外线下(365nm … 385nm) 会发出荧光，且在受到激发时发出可见的蓝光。反之，塑料表面则对紫外线表现中性。 Detection of glue on a plastic film The presence of a glue layer on a plastic film should be detected. Almost the whole width of the plastic film should be controlled. The glue is slightly UV fluorescent, whereas the plastic film is UV neutral. |
|
|||||
APP N° 214
|
检测层压板上的荧光涂层 层压板上的最终工序，会在顶层镀一层荧光涂层，SI传感器用于检测该涂层的有无。 Detection of the presence of final UV fluorescent coating of laminate The presence of the upper layer of a laminate should be controlled. At this, the layer is UV fluorescent. |
|
|||||
APP N° 206
|
棕色塑料门封条颜色检测 用于区分棕色塑料门封条的色差。 Color differentiation of brown plastic door seals Two different brown colored plastic seals should be differentiated. |
|
|||||
APP N° 205
|
塑条颜色区分 用于检测图示不同颜色塑料条的色差。 Color differentiation of plastic stripes Different colored plastic stripes should be differentiated. |
|
|||||
APP N° 197
|
研磨材料颜色的在线检测 该应用中，传感器需对研磨材料带的颜色进行在线检测。 Inline color control of abrasive material Abrasive band material should be inline color controlled. |
|
|||||
APP N° 182
|
检测中纤板上的彩线 该应用中，传感器用于检测中纤板上的红色线条。检测过程中，线条的深浅不一，同时中纤板的表面结构也由粗糙向平滑转变。 Detection of a colored line on a MDF plate A red colored line should be detected on the surface of a MDF plate. At this, the color of the stripe differs in intensity and slightly in color. Furthermore the structure of the MDF surface can also changing from coarse to fine. |
|
|||||
APP N° 146
|
检测木头表面树斑和树结 木质品表面要求光洁颜色统一，该应用中，SI传感器用于探测木头表面的深色树斑和树结等瑕疵处。 Detection of knots and bark in wooden stakes Wooden stakes should be produced free of knots and bark. |
|
|||||
APP N° 104
|
木制品直径在线检测 在木制棒材产品生产过程中，当棒材运动的时候，产品的外径需要检测。 Inline diameter control of wooden staff During the production of wooden staff the diameter must be controlled while the rod is moved. |
|
|||||
APP N° 100
|
门板喷漆后的在线光滑度/光泽度检测 门板在喷漆之后需要立即对其光滑度/光泽度进行在线检测。检测结果会反应出喷漆量是否到位。如果喷漆量不够，门板表面光滑度值会比较低，门板表面略显粗糙。 Gloss inline measurement after the varnish of doors Immediately after the varnish of the doors the gloss factor should be controlled. Tests have shown that the amount of varnish, which will be sprayed onto the door surface, influences the gloss factor. If not enough varnish is used the surface becomes rough. |
|
|||||
APP N° 88
|
砂带上荧光黏合剂的检测 用于检测砂带上的荧光黏合剂。在此应用中，检测距离是20mm，光斑大小是2mm x 10mm。 Fluorescent glue control on an abrasive belt During the production of abrasive belt material with a 10mm wide glue stripe the presence of the fluorescent glue must be observed. Defects greater than 2mm in length must be proper detected. The distance of the sensor head to the object should be approximately 20mm and the detecting range around 2mm x 10mm. |
|
|||||
APP N° 87
|
砂纸表面光滑度/光泽度在线检测 表面光滑度/光泽度是衡量砂纸质量的一个重要因素，因为其光滑度必须在生产的过程中在线进行检测。 Inline gloss measurement on abrasive belts The gloss factor is a significant parameter for the surface quality, the roughness, of an abrasive belt. Thus a gloss measurement inline sensor should be used for quality control of the abrasive surface. |
|
|||||
APP N° 77
|
砂带的边缘检测 砂带的边缘需要打磨成一个特定的角度，因此，该角度需要被检测控制。 Edge control of abrasive belts The edges of abrasive belts must be grinded to a certain degree. Thus, the degree of grinding should be controlled. |
|
|||||
APP N° 74
|
塑料膜及复合板的在线光滑度/光泽度检测 家具行业的塑料膜及复合板在生产的过程中光滑度/光泽度需要在线检测。 Inline gloss measurement of plastic films and laminated plates During the production of plastic films as well as of laminated plates the gloss factor should be measured. |
|
|||||
APP N° 67
|
家具行业光滑度/光泽度在线检测 在制作门板的过程中，喷漆之后即需要对门板的光泽度进行在线检测以保证产品的质量。 Inline gloss control in the furniture industry During the manufacturing process of doors just after the painting line the amount of color must be controlled. |
|
|||||
APP N° 66
|
家具行业颜色监控 在生产门板的过程中，门板的颜色必须被检测。该检测用于反馈给机器人喷枪，来控制喷漆量。该检测过程在喷漆流程之后，烘干流程之前。 Color monitoring in the furniture industry During the manufacturing process of doors the color must be controlled and monitored. At this the color will be sprayed with spray nozzles, which are mounted on a robot, onto the doors. Just after this process but before the drying process the color should be controlled. |
|
|||||
APP N° 51
|
砂带边缘控制 各种砂带都会加边。此砂边位于砂带砂面和侧面之间。此边颜色一般比砂带砂面颜色浅但是比侧面颜色深。根据此色差，这条砂边的颜色及位置可以有效的被颜色传感器识别。 Control of margined abrasive belts Different sanding belts are equipped with a margin and this margin has to be controlled. The margin can be present on the sanding side of the abrasive belt or on the rear side. Furthermore the margin can be darker than the rear side but mostly it is brighter than the sanding surface. Nevertheless there is a sufficient difference in contrast between the margin and the rear side or the sanding side. |
|
|||||
APP N° 47
|
检测木板上的荧光标记 木板上有缺陷的地方已使用荧光标记出来。荧光标记的宽度通常在15mm左右，有时两条标记的间距仅有20mm，传感器需要能够分别识别这两条标记。传感器需在距离被测物200mm处进行检测，且要能够识别宽度仅有5mm的标记。 Color detection of fluorescent marks on wood plates On wooden plates defects will be marked with a fluorescent marker. The fluorescent mark has normally a width of about 15mm and it can happen, that two of this marks lie 20 mm away of each other, but must be detected as two separate marks. Furthermore the fluorescent marks should be detected at a distance of 200 mm to the object and even a mark with a width of 5mm should be detected. |
|
|||||
APP N° 21
|
颜色信号的记录及监控 越来越多的SPECTRO-3颜色传感器用户提出需要一款能够对颜色进行监控并记录的软件。生产诸如塑料薄膜等不间断材料的厂商和叠层中纤板制造商需要一款在线传感器系统，它不仅能够进行100%的质量控制，同时还能对颜色信息进行记录，如产品编号、客户名称或数量、合同号、操作人员姓名、时间和日期等。同时，该系统能为操作者提供产品的颜色趋势，以便操作者能够采取相应的对策。 Color signal recording and color signal monitoring More and more users of the SPECTRO-3 color sensors are asking for a color monitoring and color recording software. The manufacturers of endless materials like plastic foils (e.g. furniture, paper and automotive industry) and the fabricators of laminated medium density fiberboards (MDF) needs an inline sensor system not only for a 100% - quality control but beyond that a system for color signal recording, which allows also to document data like product number, customer name or number, order number, operator name, time and date. Furthermore, the sensor system should inform the operator about the color trend of the product, thus possible countermeasures can be duly initiated. |
|
|||||
APP N° 18
|
木材加工业和造纸行业中传送带的横向位置控制 木材加工业（生产中纤板）和造纸行业中需要使用特殊的传送带。带子横向位置需控制在±0.2mm范围内，纵向位置可在±2mm间变化。传送带材料为不锈钢或塑料织物。 Lateral position control of conveyor belts in the wood and paper industry In the wood industry (during the production e.g. of MDFs = medium density fiberboards) as well as in the paper industry, special conveyor belts are in use. The lateral position of the band material must be hold in a range of ±0.2mm, whereas the vertical position can change in the range of ±2mm. The material of the conveyor belt is either stainless steel or plastic fabric. |
|
|||||
APP N° 5
|
薄木贴面板质量控制 1.检测门生产过程中薄木贴面板的轻度烧痕和裂纹 薄木贴面板粘贴到中纤板的过程中如遇到外界因素干扰，可能导致热风枪轻微烤焦贴面板表面，SI可用于检测生产过程中薄木贴面板产生的轻度烧痕和裂纹 2. 分辨白色反光薄木贴面板和白色哑光薄木贴面板 SI传感器可用于分辨白色反光和哑光薄木贴面板。 Veneer control during the door production 1. Detection of slightly burned veneer zones and veneer tear-off during the door production: The veneer will be glued onto the mdf plate during the movement, however, if the process will be interrupted due to any reason, it can happen, that the hot air gun, which will be used normally to warm up the glue, scorches or burns the veneer surface slightly. Furthermore the color sensor should detect a veneer tear-off. 2. Differentiation between white glossy veneer and white matt veneer: The task is to distinguish between white glossy and white matt veneer. |
|
)
TOP