N° 531
|
Detection of holographical reference marks
Holographic reference marks should be detected. There are red as well as green reflecting reference marks which should be detected with the same adjustment.
|
|
N° 412
|
Kantdetektion og optælling på filtermateriale På forskellige filtertyper skal antallet af buk optælles.
Edge detection at bellows (fold counting)
On bellows the edges should be detected and counted.
|
|
N° 353
|
Doppeltlagskontrol på kunststoffolie Kanten på en dobbeltlags plastfolie, skal overvåges. I kanten går folien over til at være enkeltlags.
Double layer control of plastic films
With a view to the changeover from the double layer to the single layer range of a plastic film a sensor system should deliver exactly a signal which informs about the beginning of the single layer as well as the double layer range.
|
|
N° 328
|
Dobbeltlagskontrol på papirark To på hinanden placerede papirark skal skelnes fra enkeltsider.
Double layered paper sheet control
Double-layered paper sheets should be differentiated from single sheets.
|
|
N° 312
|
Detektering af forskellige farvemærker på forskelligt farvede plastbeholdere På kunststoftuber i forskellige udførsler, skal farvemærker genkendes.
Detection of different color marks on different plastic tubes
Different color marks should be detected on different plastic tubes.
|
|
N° 296
|
Aftastning af fortykkelse på et hurtigt bevægende kunstfiberbundt Et kunstfiberbundt skal aftastes med henblik på at overvåge for fortykkelser. Til opgaven anvendes en fiberforsats direkte rettet op under fiberfremføringen, som derved ikke påvirkes når der ikek er fortykkelser, men giver udslag når disse opstår.
Detection of a ravel in a fast moved plastic fiber bundle
A ravel in a fast moved plastic fiber bundle should be detected. At this, an optical fiber through beam head is placed in way, that the normal plastic fiber bundle stream does not cover the optical beam. However, if a ravel appears, the optical beam will be partly interrupted and this leads to a decrease of the receiver signal.
|
|
N° 291
|
Glanskontrol på halvleder metalstriber Glansen på blyrammer skal kontrolleres på steder hvor halvledere skal placeres senere i produktionen.
Lead frame gloss control
The gloss of lead frames should be controlled. At this, the surface where the semiconductor chip should be placed can be blank or rough.
|
|
N° 287
|
Farvemærkeaftastning på en trykt alubelagt folie Et sort farvemærke skal aftastes på en alu-belagt folie. Til nøjagtig positionering af folien skal sorte farvemærker på en alubelagt folie aftastes. Til signalgivningen skal anvendes et digitalt signal.
Color mark detection on aluminum coated plastic film
Color marks should be detected on aluminum coated plastic foil. An analog as well as a digital signal is required at the sensor output.
|
|
N° 281
|
Udkastkontrol på stansedele I forbindelse med sikringen af et stanseværktøj skal monteres en udkastkontrol af de stansede dele. De små dele bliver i kontrolleret og talt i frit fald. Hastigheden kann være på til få m/s.
Ejection control of stamping parts
Due to stamping tool protection reasons the ejection of very small stamping parts should be controlled and the parts counted. The ejection speed of the parts is in the range of a few m/s.
|
|
N° 260
|
Niveaukontrol af transparent støbemasse i SMD – LED Niveauet af en transparent støbemasse i SMD – LED’er skal overvåges med henblik på at undgå underfyldning.
Underfilling control of SMD LEDs
The level of transparent casting compound in SMD LEDs should be controlled with a view to underfilling.
|
|
N° 256
|
Optælling af blikplader til vandkølesystem Antallet af blikplader i en pakke, skal tælles under bevægelse.
Counting of dishes for water cooling systems
The number of dishes in a package should be counted during the movement of the package.
|
|
N° 240
|
Overvågning af koncentrisitet på en skive Koncentrisiteten på en hurtigt roterende skive skal kontrolleres.
Concentric runout control of a wheel
The concentricity of a high speed wheel should be controlled.
|
|
N° 239
|
Genkendelse af farvemærke på transparent kunststof Et farvemærke på en transparent plastfolie, skal aftastes. Applikationen befinder sig i Ɛx – området, hvilket betyder at man helst skal bruge lysleder.
Detection of a color mark on a transparent plastic film
A color mark on a transparent plastic film should be detected. The sensor is used in the Ɛx – range, thus, an optical fiber unit is necessary.
|
|
N° 237
|
Positionskontrol af farvemærker Positionen af et aluminiumsfolie eller kunststoffolie, med trykte farvemærker skal aftastes. Både kann ændre sig fra gang til gang. Derfor skal der bruges et meget fleksibelt system, som kann tilpasses let. Ved siden af det digitale signal, som sættes ved dækning af 50 % af lyspletten. Sensoren des et analogsignal, som viser den aktuelle position af farbmærket under lyspletten: 5V betyder 50% dækket, 0V og 10V (alt efter om baggrunden er lys (så 10V) eller mørk (da 0V)).
Color mark position control
The position of printed color marks on aluminum foils and plastic films should be controlled. At this, the sensor system should deliver an analogue signal which is proportional to the position of the color mark. At this, the color of the background as well as of the color mark can change from batch to batch, which means, that a flexible “easy to handle” system is required. Beside the digital output (a signal change should happen if the light spot is covered by 50% of the color mark) there is an analog output desired, which informs about the actual position of the color mark: 5V means, that the light spot covers to 50% the color mark and 0V and 10V shows, that the light spot falls either only onto the background or onto the color mark.
|
|