Praktische Beispiele aus dem industriellen Einsatz
1) Einsatzbereich auswählen:
Construction Industry / Ceramic-finish Industry (Bauindustrie / Keramikverarbeitung)
2) Sprache auswählen:
APP N° 727
|
Thickness measurement of thermal insulation panels The thickness of thermal insulation panels should be measured INLINE. |
|
|||||
APP N° 698
|
Distance measurement to insulation panels The distance to insulation panels should be measured. |
|
|||||
APP N° 681
|
Color and intensity control of filament lamps The color as well as the intensity of filaments lamps should be controlled. |
|
|||||
APP N° 587
|
Moisture control of bricks The moisture of bricks should be controlled. |
|
|||||
APP N° 586
|
Moisture control of clinker bricks The moisture of clinker bricks should be controlled. |
|
|||||
APP N° 585
|
Moisture control of concrete blocks The moisture of concrete blocks should be controlled. |
|
|||||
APP N° 584
|
Moisture of gas concrete The moisture of gas concrete should be controlled. |
|
|||||
APP N° 527
|
分辨涂层的和未经涂层的地砖的光泽度 应区分涂层的地砖与未经涂层的地砖。 Gloss differentiation of coated flagstones from uncoated flagstones Coated flagstones should be differentiated from uncoated flagstones. |
|
|||||
APP N° 522
|
釉面瓷砖的色检 应在生产线上检测釉面瓷砖的颜色。 Color measurement of glazed tiles The color of glazed tiles should be inline measured. |
|
|||||
APP N° 503
|
石板的高度检测 在用输送带输送石板期间应检测石板的厚度。首先，输送带造成的高度波动可以忽略不计，因此可以将之作为参考值。 Stone plate thickness control The thickness of stone plates should be measured. At this, the stone plates will be transported on a conveyor belt with a negligible movement in height, thus it can be used as a reference. |
|
|||||
APP N° 490
|
抛光石板的厚度测量 应测量石板的厚度。在此应注意，石板是放在一块参考板上传送的。 Thickness measurement of polished slabs The thickness of polished slabs should be measured. It should be noted, that the slabs are placed on a reference plate. |
|
|||||
APP N° 489
|
抛光石板的光泽检测 应检测抛光石板的光泽。 Gloss measurement on polished slabs The gloss of polished slabs should be measured. |
|
|||||
APP N° 488
|
抛光石板的色检 应检测抛光石板的颜色。 Color control of polished slabs The color of polished slabs should be controlled. |
|
|||||
APP N° 470
|
检测屋面瓦的颜色 应能在生产线上检测出屋面瓦的颜色。 Roof tile color measurement The color of roof tiles should be inline measured. |
|
|||||
APP N° 453
|
测量一块石膏板的长度 应测量一块石膏板的长度。 Measurement of the length of gypsum plasterboard The length of gypsum plasterboard should be measured. |
|
|||||
APP N° 346
|
天花板系统光栅带的色检 应检测天花板系统用的可见光栅带的颜色。 Color control of T-grids for ceiling systems T-grids used for ceiling systems should be color controlled. |
|
|||||
APP N° 333
|
监测工业鼓风机的频率 应监测工业用鼓风机的频率。此外，也应检查旋转方向。 Frequency control of industrial ventilators Ventilators for industrial purposes should be frequency checked. Furthermore the direction of rotation should be controlled. |
|
|||||
APP N° 294
|
测量包覆有发光铝箔的靠垫的厚度 应测量包覆有发光铝箔的靠垫的厚度。此靠垫用于隔热 (热绝缘)。在此，铝靠垫被传送带传送，该传送带的高度稳定，因此可用作间隔基准。 Thickness control of shiny aluminum cushions The thickness of different shiny aluminum cushions should be measured. These aluminum cushions are used for heat insulation. At this, the cushions will be transported on a conveyor belt with a very small fluctuation in height, thus the distance to the belt can be used as a reference. |
|
|||||
APP N° 289
|
检查切割圆盘的平整度 应在旋转期间检查所谓的切割圆盘的平整度。 Evenness control of angle grinder discs The flatness of angle grinder discs should be controlled during the rotation. |
|
|||||
APP N° 149
|
瓷砖加湿情况控制 瓷砖在加湿以后（喷水）需要检测加湿程度是否达标。加湿程度不够和加湿过度都属于不合格产品。 由于加湿程度不同，瓷砖颜色也不一样，因此SI颜色传感器可于加湿后通过检测颜色来检测加湿是否到位。在此应用中，如果加湿程度不够，瓷砖颜色会更白，如果加湿过度，瓷砖颜色会更深。 Differentiation between water moistened and dry floor tiles After the moisturization the floor tiles should be checked, whether the amount of moisture is in the right range or out of range (too much or too little moisture content). The tiles looks brighter if the degree of moisture is too small and the tiles looks darker as normal if too much water is on the tiles. In the normal case the tiles looks gray in color. |
|
|||||
APP N° 144
|
瓷砖方向检测 如图所示应用，该瓷砖表面有三条倒棱，将瓷砖分为四部分。当瓷砖在传送带上走动时，SI传感器用于检测该瓷砖的放置方向。该应用正确的放置方向应该是倒棱线垂直于传送方向。 Position monitoring of tiles The orientation of tiles on a conveyor belt should be controlled. There are three chamfers which splits the tile into four parts and these chamfers should be perpendicular orientated on the conveyor belt. |
|
|||||
APP N° 134
|
检测铝管内有无纤维丝状物质 在此应用中，铝管长度约为160mm，内径约为14mm。合格的铝管内无任何杂物，而不合格的产品内部则清晰可见有纤维状的丝状物质存在。在检测过程中铝管可360度旋转，SI传感器可准确将不合格产品检测出来。 Control of the presence of fibers in an aluminum tube In aluminum tubes with a length of approximately 160mm and an inner diameter of 14mm the presence of fibers should be checked, at which a good tube is a tube without any fibers. The tubes can be positioned and turned 360° around, around both ends of the tube there is space enough for mounting the sensors. |
|
|||||
APP N° 105
|
喷涂量控制 对喷嘴的喷涂量/喷涂浓度进行控制。 Spray jet amount control The density of the spray jet should be controlled. |
|
|||||
APP N° 88
|
砂带上荧光黏合剂的检测 用于检测砂带上的荧光黏合剂。在此应用中，检测距离是20mm，光斑大小是2mm x 10mm。 Fluorescent glue control on an abrasive belt During the production of abrasive belt material with a 10mm wide glue stripe the presence of the fluorescent glue must be observed. Defects greater than 2mm in length must be proper detected. The distance of the sensor head to the object should be approximately 20mm and the detecting range around 2mm x 10mm. |
|
|||||
APP N° 87
|
砂纸表面光滑度/光泽度在线检测 表面光滑度/光泽度是衡量砂纸质量的一个重要因素，因为其光滑度必须在生产的过程中在线进行检测。 Inline gloss measurement on abrasive belts The gloss factor is a significant parameter for the surface quality, the roughness, of an abrasive belt. Thus a gloss measurement inline sensor should be used for quality control of the abrasive surface. |
|
|||||
APP N° 77
|
砂带的边缘检测 砂带的边缘需要打磨成一个特定的角度，因此，该角度需要被检测控制。 Edge control of abrasive belts The edges of abrasive belts must be grinded to a certain degree. Thus, the degree of grinding should be controlled. |
|
|||||
APP N° 57
|
不同泡沫材料表面荧光标记线的检测 用于检测不同泡沫材料表面荧光标记线。 Detection of a fluorescent line on different colored foamed materials A fluorescent line must be detected on different colored foamed materials. |
|
|||||
APP N° 51
|
砂带边缘控制 各种砂带都会加边。此砂边位于砂带砂面和侧面之间。此边颜色一般比砂带砂面颜色浅但是比侧面颜色深。根据此色差，这条砂边的颜色及位置可以有效的被颜色传感器识别。 Control of margined abrasive belts Different sanding belts are equipped with a margin and this margin has to be controlled. The margin can be present on the sanding side of the abrasive belt or on the rear side. Furthermore the margin can be darker than the rear side but mostly it is brighter than the sanding surface. Nevertheless there is a sufficient difference in contrast between the margin and the rear side or the sanding side. |
|
TOP